Fridge Freezer Control PCB Module Stock Number: ES1671223
Genuine spare part for select models of Beko and Blomberg fridge freezers
Beko CDA565 upper fridge now becoming a freezer what parts can I replace to correct fault. I keep seeing that the thermostat cannot be replaced is this correct? 2 Answers
- Mine has become a freezer too, any advice please ? been quoted £125 for a call out
-
Dean at eSpares says...
It is difficult to test the PCB so check for any signs of damage if the internal sensors have failed we believe they are not replaceable.
Fridge freezer stays on the whole time resulting in fridge becoming a freezer. This suggests a thermostat issue. 1 Answer
Lamona/Becko HJA 6855E1. There is a pcb with temperature knob in the light housing and another main pcb on the back. The black sensor on the evaporator seems to change resistance when heated by holding. Which is the most likely pcb to cause this.
-
eSpares Staff at eSpares says...
The sensor does change resistance when it changes temperature which is perfectly normal.
I have a beko fridgefreezer,K60315H/B776, and it doesn't get cold in either the fridge or freezer. All looks free from dust etc. The light in the fridge comes on but I don't here any noises from the unit or compressor,any ideas on the part to replace 1 Answer
As above in the question I am not sure if it's the compressor or the PCB? I don't want to spend a fortune fixing it has it's only my garage fridge but would be nice to fix. If you could advise it would be very appreciated.
-
eSpares Staff at eSpares says...
You would need to use a multimeter to test the components starting with the compressor first, you cannot test the PCB so look for any signs of damage.
The temperature in my freezer is swinging from +3 to -22. Can you advise is it PCB, compressor or thermostat. If thermostat is it changeable?
-
Dean at eSpares says...
In order for us to help we would need to identify your model’s details, please provide us with the following information: Appliance make, model and the serial number of your appliance. For further help visit the "Finding Model Numbers" page on our website here: http://www.espares.co.uk/findingmodelnumbers. Alternatively please copy and paste this link into your web browser.
Hi can you help with a Beko fridge freezer 5 years old . The compressor is running and the internal fan is also running . The freezer is not cold and i have checked for any ice build up underneath the plastic panel inside the freezer which is ok. 1 Answer
The model is K54299H / B725 u Serial number 1210147908
-
Chris at eSpares says...
If the compressor is running there should be cold areas om the freezer evaporator unless there is a compressor/system fault which would require a refrigerator systems engineer to repair.
Hi there. The fan on my Beko CDA543 fridge freezer runs constantly resulting in frost covering the top half of the back of the refrigerator. If I turn the fridge freezer off and on at the mains the fan stays off until the temperature rises enough for it to kick in again, but then it won't turn off until I reset everything by flicking the mains again. I suspect the problem is the "irreplaceable" sensor located in the insulation at the back of the fridge wall. I have seen a hack on how to access this and would like to replace it by cutting a square from the insulation t. Is it possible to acquire a compatible sensor or do you think something else may be causing the problem. Many thanks
-
Chris at eSpares says...
The sensors Stock Number: ES1603782 and Stock Number: ES1584523 and have links to some fitting information in the product descriptions.
Hello my fridge freezer has become just a freezer....the fridge part gets too cold even when the temp control is set to min.....does this part control the temp?
-
Chris at eSpares says...
This part is unlikely to be the fault. The main control panel at the back may be the cause or the sensor in the lining of the fridge (the sensor cannot be replaced).
Hi i have a beko fridge freezer, K60315H / B776 model, the fridge will not cool or freezer freeze i is it this small pcb at fault or the one under the cover on the rear of the appliance or something else? 1 Answer
-
Chris at eSpares says...
If the compressor is running the appliance should be cool and if not there would likely be a system fault. If the compressor is hot but not running a faulty compressor is the problem. if cold and not running it may be the PCB at the back. For further help visit the "Finding Model Numbers" page on our website here: http://www.espares.co.uk/findingmodelnumbers.
-
Chris at eSpares says...
This is the control PCB but your problem is likely to be either the sensor (cannot be replaced) or the main board on your fridge freezer.
Will this part fit my appliance?
Check Now