Circular Fan Oven Element - 2500W Stock Number: ES507407
Spare part for select models of Tricity Bendix, AEG, Electrolux, and Zanussi ovens
Main oven has started tripping my electrics. Grill and top oven all ok. But as soon as the main oven is turned the power trips out.
- your element has shorted to earth replace element
- its the main cooker element has blown,so triping out,i had exactly the same,fitted new one now better than before
- yes it should do. when an element goes it melts together and it could cause a short circuit other causes could be loose wiring on element
- It is possible that the main element has been damaged and it is causing an electrical short. Sometime the circular rigns fuse together and that may cause the short.
-
Rory at eSpares says...
Hi Huxley Without actually seeing your oven, it is impossible to tell what is causing this problem. What I would advise is talking to your local cooker specialist and they should be able to diagnose the problem for you. And that's where we come in! With thousands of oven spares, we're bound to have the part for you.
My oven has a top oven and a bottom oven. Which one is this element for? (I need one for the bottom oven!) 4 Answers
Zanussi ZHQ575x
- This element is for the BOTTOM OVEN of a Zanussi ZHQ575. To replace, gently unclip the thermostat from the top right hand corner of the back plate, unscrew the back plate and old element, pull the spade connectors from the element taking care that the wires don't spring back into the holes. Push the connectors on to the new element and reattach the element and backplate to the cooker. Clip the thermostat back in place. Should take no more than about half an hour.
-
eSparesMalindi at eSpares says...
Please contact us with your full model details so that we can help you get the correct element for your appliance. Hopefully this link helps: http://www.espares.co.uk/findingmodelnumbers.aspx
- normally the top oven doesnt have a fan,the only element is for the grill.you can tell if that is working ,by turnig on and see it glowing ,therefore element would be in the bottom oven.but have you checked your thermostat! my advice is do the element first ,as these normally go first,they are very easy to fit ,and dont take much time at all. hope this helps.
- This is definitely the one! You just unscrew the plate at the back and the old element, then pull the crimped wires off (this is the hardest bit - I used pliers) then reassemble. If the lights all come on and it doesnt warm up then its definitely the element!
Fitted the new element in bottom oven nothing is working in the bottom oven including the light the top oven works what is my problem 1 Answer
-
Chris at eSpares says...
Make sure you have reset the clock as this stops the oven working. For more information search our advice centre.
Have removed the old element but the clips keep popping off the new element so haven't yet screwed element in. How can I make the wire clips stay attached?
-
Chris at eSpares says...
If the clips you refer to are the spade connectors for the wires to the element it is possible to tighten these by gently squeezing the rolled end to reduce the gap. If the connectors are in poor condition they can be replaced by cutting off the old ones and obtaining new from most car spares shops.
It says I need top check the pnc number against the 'list of appliances' but where is the list of appliances? Could not find on the page,nor found with search..can you confirm which I need - details below... 1 Answer
John Lewis oven model JLBIDOS904 Product number 944171399 Serial number 64900009
-
Caitlin at eSpares says...
The element you need for that model and product number is our stock code ES1007939
I have tried all morning to unscrew the front panel to access the element I have tried WD40 and a lot of it but the screw are so stuck. Did you ever came across with this before? Do you have any suggestion? I really want to try to save some money and do it myself cheers
- I had a similar issue but with just 1 screw on my front panel. It has corroded into the clip at the back and in my effort to unscrew it the cross head just rounded out. I used a dremil to cut the head of the screw into a flat so i could use a flat blade screw driver. After a bit of wigling about the screw came out and i replaced it with a new one.
I've changed the fan and element. The old element was open circuit, the new one had a reading of 22 ohms. So I believe the element went and took out the 32amp breaker in the fuse board. Is there something else that might have blown at the same time? or a reset device? Electrolux EOU6330X
- USE A TEST METER FOR TESTING THE POWER AT THE TERMINALS BE VERY CAREFUL THE WHOLE THING WILL BE LIVE.
- Just supply cooker make,model number,& serial number to espares then you will get the right item
Will this part fit my appliance?
Check Now